#PROGRAM REJECTED INVALID POLICY SCCM SERIAL#

% UC_CMI-3-SerialPortGetStatusError:В %:В When CMI tries to get the status of serial port, the operating system returns an error.Д®xplanation CMI triggers this alarm when it can't get the status of the serial port.

Also, physically confirm that the cable is firmly connected to the USB0 port. Recommended Action Ensure that USB0 is configured in the Cisco Messaging Interface service parameter Serial Port. CMI triggers this alarm if the value in the Serial Port service parameter is anything other than USB0. It is possible that the Serial Port value has been updated via AXL or a CLI command where validation of the value was not performed. % UC_CMI-1-SerialPortOpeningError:В %:В When CMI tries to open the serial port, the operating system returns an error.Д®xplanation For a system running CMI, the serial port through which the voice messaging system is connected is always USB0, and that value is configured in the Cisco Messaging Interface service parameter, Serial Port. Recommended Action Contact the vendor of the third-party voice messaging system and discover why it is sending SMDI message with an invalid format CMI triggers this alarm if the received MWI message doesn't have one of the acceptable formats as described. The second deactivates the message waiting indicator. The first message activates the message waiting indicator (MWI). % UC_CMI-5-SMDICmdError:В %:В CMI receives an invalid incoming SMDI message.Д®xplanation There are two kinds of incoming messages that Cisco Unified Communications Manager can accept from the voice messaging system they are OP:MWI(SP)nnnnnnn!(D) and RMV:MWI(SP)nnnnnnn!(D) (where:nnnnnnnnnn = station number (can be 7 or 10 digits), (D) = End Of Transmission, (SP) = space). Recommended Action Verify that the Cisco Messaging Interface service parameter Validate DNs is set to false

In such cases, if the Validate DNs service parameter is set to True, CMI triggers this alarm because the DN cannot be found in the Unified CM database. % UC_CMI-5-SMDIMessageError:В %:В SMDI message contains invalid DN.Д®xplanation Some voice messaging systems send SMDI messages to Cisco Unified Communications Manager (Unified CM) with an invalid DN specifically for the purpose of verifying that Unified CM is functioning properly. Recommended Action Verify that the Cisco Messaging Interface service parameter Parity is set to a valid (allowable) value For this reason, it is best to set this value in the Service Parameter Configuration window in Cisco Unified CM Administration so that the value can be validated against the accepted range of values for this field. It is possible that the parity value has been updated via AXL or a CLI command where validation of the value was not performed. % UC_CMI-1-ParitењњonfigurationError:В %:В The CMI service parameter, Parity, has an invalid configuration.Д®xplanation An invalid parity has been configured for the serial port that CMI uses to connect to the voice messaging system. Recommended Action Verify that the Cisco Messaging Interface service parameter Stop Bits is set to a valid (allowable) value It is possible that the Stop Bits value has been updated via AXL or a CLI command where validation of the value was not performed. % UC_CMI-1-StopBitConfigurationError:В %:В The Cisco Messaging Interface service parameter, Stop Bits, has an invalid configuration.Д®xplanation An invalid stop bit has been configured for the serial port that CMI uses to connect to the voice messaging system. Recommended Action Informational purpose only no action is required % UC_CMI-6-CMIServiceStatus:В %:В Service is running and working properly.Д®xplanation CMI service is running and working properly If this occurs, the error message is given a severity-level of 3, irrespective of the default severity-level for that error message. If the error message contains UNKNOWN_PARAMNAME, the parameter immediately following the UNKNOWN_PARAMNAME has not yet been updated in the alarm catalog. Order of the parameters in an alarm message can change and it is decided by the Application or Component. Application or Component may decide not to use that parameter in the alarm message. Optional parameter is indicated with the notation.

Program rejected invalid policy sccm